Setting up A Bathtub
Setting up A Bathtub
Blog Article
Were you trying to find facts and techniques about Installing A Bathtub?
Setting up a bathtub isn't exactly brain surgery, however it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a moderately difficult task. If the old bathtub is readily accessible, the job can move speedily; if you need to open a wall surface to eliminate the old bathtub as well as position the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the task and also are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed project, it is much better to consider employing one before you start. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly help you set up a brand-new tub in your washroom if you have already acquired a new bathtub and also don't require to change the plan of your previous water pipes.
Your tools as well as material list should make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain any water staying in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. When the supply pipes have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this procedure. As soon as the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a link to the existing supply pipelines.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making sure that the washing machines are in location between the tap and also the sink. Safeguard the faucet in position with the maker offered backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former type needs to be attached to the tap ends first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Making use of both wooden boards under its feet, place the bath tub in the needed position. The wooden boards are handy in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub till the spirit level reads degree.
To set up taps, fit all-time low of the furthest adaptable faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if necessary. Load the bathtub as well as also inspect the overflow electrical outlet as well as the regular electrical outlet for leaks.
Lastly, fix the bathroom paneling as defined in the producer's user's manual. Tiling and securing around the bathtub should wait up until the bathtub has actually been utilized at the very least when as this will resolve it into its last setting.
Preparing for the Setup
Firstly, the sustaining frame provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes as well as cartridges, and can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to allow for the movement experienced when the bathtub is in use. The sealer can break fairly very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very occupied with How to Install a Bathtub Yourself and I hope you enjoyed the entire blog post. Sharing is nice. Helping others is fun. Thank you so much for your time invested reading it.
Schedule A Service
Report this page